Hot water submersible pump
It is suitable for hot water well,hot spring,farmland irrigation,garden watering,fountain landscape,rainwater recycling system,mine drainage,emergency,urban water supply,enterprises and institutions carrying the underground water with the advantages of low noise,high efficiency,and energy saving.
Use conditions:
It is suitable for hot water well,hot spring,farmland irrigation,garden watering,fountain landscape,rainwater recycling system,mine drainage,emergency,urban water supply,enterprises and institutions carrying the underground water with the advantages of low noise,high efficiency,and energy saving.
Zhonglan submersible water pump introduction:
Zhonglan QJR series stainless steel well submersible pumps ,designed for pumping high temperature liquid,it is composed of YQS submersible electric motor and QJ submersible electric pump in directly connection. The parts of the pump are precisely manufactured by HT200 materials. It adopts mixed-flow or centrifugal single-suction multi-stage pump body structure,with built-in one-way valve and suction filter;the impeller is fixed on the pump shaft by a unified key,and is equipped with a pump shaft protection sleeve.The submersible motor adopts water-lubricated bearing,and the upper is equipped with sand thrower and skeleton oil seal to prevent mud and sand from entering the motor. This series pumps are chacteristic of compact structure,reliable operation,durability,easy to use,large power,less trouble,low maintenance cost,etc. As long as the motor filled with clear water,the pump can run normally.
Zhonglan Hot water submersible pump characteristics:
Impeller:stainless steel cast iron material 304/316
Pump shell:cast iron HT200,or stainless steel i.e.2Cr13,304
Pump shaft:cold drawn steel with Chrome plated,or stainless steel 2Cr13(tempering treatment at 1050℃,strengthening torque)
Motor seal:rubber seal 0 -ring,mechanical seal
Motor expansion control bag is made of rubber.
Performance parameters:
Pump medium: similar to water,a high-temperature liquid with a solid content of 0.02% or less.
Temperature of medium: maximum 125℃ for deep well hot water pump
PH value of medium:3-10
Power : frequency 50Hz,60Hz( can be customized)
Rated voltage 380V[660V、1140V、3000V、10KV]±5%
Flow range:5-2600m3/h
Water head range :2-1500m
power range:3-3800kw (secondary speed motor,can be customized four-stage/ six-stage motor)
Rotating speed:2900rpm(secondary speed motor)
Remarks:
1.Deep well pump should be used in clean water with a content of less than 0.001%,pump house is equipped with pre-moistening water tank,the capacity should meet a start pre-moistening water.
2.For newly installed or overhauled deep well pumps,should adjust the clearance between the pump shell and the impeller,ensure no friction between the impeller and the pump shell during running.
3.Before the operation of the deep well pump ,clean water should be filled into the house of the shaft and bearing for pre-moistening
4.Before starting the deep well pump,the inspection items should meet the following requirements:
1）Base bolts have been tightened.
2）The axial clearance meets the requirements,the safety nut of the adjusting bolt has been installed.
3）The packing gland has been screwed and lubricated.
4）The motor bearing are lubricated
5）Rotating the rotor and the stop mechanism by hand are flexible and effective.
5.The deep well pump should not be idled without water. The primary and secondary impeller of the pump should be immersed below 1m water level,pls check the change of the water level in the well frequently during running.
6.During running,when found there is a large vibration around the foundation,then should check the pump bearings or motor packing wear,when there is excessive wear and water leakage,then should replace new pieces.
7.The deep well pumps containing mud and sand have been sucked and discharged,before stopping the pump, should rinse the pump with clean water.
8.Before stopping the pump,should first close the outlet valve,cut off the power supply,lock the switch box. When it is winter,should release the water in the pump completely.
Why choose us? 3 advantages:
1.quick delivery! Stock pumps can be shipped quickly;
2.Reliable quality! Manufacturing pumps many years, have a number of new and old customers;
3.Competitive price! Manufacturer supply directly without middlemen.
We are professional Hot water submersible pump manufacturer. If you want to know more related products, please click here.
https://www.zl-waterpump.com/
